Workstands

Everyone wears out their Park Tool work stand clamp covers at some point. Find replacement covers for yours here. Each cover is constructed of soft, durable composite rubber. See below to determine which covers fit your Park Tool stand clamp: - 1002: fits 100-3X and 100-5X extreme range clamps - 1185: fits clamps on the repair stands PCS-9, PCS-10, PCS-11, and PCS-12 - 1259: fits 100-4X, 100-6X, 100-7X, and 100-15X clamps - 1960: fits 100-3D, 100-5D, and 100-25D Professional Micro Adjust Repair Stand Clamps - 468B: fits clamps with double cable reliefs, including 100-3C, 100-5C, 100-8C, 100-8Y, and 100-9C clamps - 467B: fits clamps with single cable relief, including PRS-2 through PRS-8 (for older-style clamps, non-current) - 468G: fits PCS-1 and PCS-2 clamps with double cable reliefs (clamp models: 100-1C, 100-1CA, and 100-2C) - 467G: fits PCS-1 and PCS-2 clamps with single cable relief (for older PCS-series stands only; not for current model stands) - 466: Rubber Replacement Clamp Cover Set (fits older clamps with plastic-dipped jaws)

Park's adjustable linkage shop clamp is found in more shops than any other professional level clamp. The 100-3C features solid cast aluminum construction and durable replaceable clamp covers. Clamp has reliefs on both jaws for cable routing. - Fits all generations of PRS-2, PRS-3, and PRS-4 stands, and PRS-5 stands manufactured before 6/96 - Fits bike frame tubes from 1" to 1-5/8" (25mm to 41mm) - The clamp jaws are nominally 4 inches (10cm) wide - Uses 468B jaw covers

Traveling mechanics choose the Super-Lite Team Race Stand because this Euro-style stand securely holds bikes without clamping the frame tubes or seatpost but by gripping the front or rear dropouts via quick releases. This is ideal for bikes with ultra-light frame tubes and seatposts, and for bikes with tight access areas that can't be clamped. For easy wrenching, this stand rotates horizontally 360 degrees and can be adjusted up and down from 28 to 38 inches (bottom bracket to the ground). Plus, the gossamer 13.5-pound weight makes it the ideal choice for traveling mechanics everywhere.

The PRS-26 incorporates proven features from our other Team Issue stands to produce a strong, lightweight repair stand that's at home on-the-go or in the race pits. The sturdy tripod leg design folds and unfolds quickly and easily, and provides stability on any surface. The clamp is height-adjustable from 97 to 147 cm (38" to 58"), and can be positioned over one leg or between two legs to accommodate any bike. Precisely constructed from anodized 6063 T6 lightweight aluminum and durable composites, the PRS-26 is our lightest full-featured repair stand, and folds compactly for storage or transport. The PRS-26 is equipped with the time-tested 100-25D Micro-Adjust Clamp, the same design featured on our shop repair stands. The 100-25D features narrow clamping jaws to fit into tight areas or on short seat posts, and clamps nearly any tube from 23 to 76 mm (7/8" to 3"), including aero tubes and dropper posts. The cam-actuated adjustment system allows for quick entry, adjustment and exit. - Maximum weight capacity*: 36 kg (80 lbs.) - Clamp capacity: round and aero tubes from 22 to 76 mm (7/8" to 3") wide - Jaw width: 70 mm (2.75") - Height adjustable from 97 to 147 cm (38" to 58") - Base when open forms a triangle of 126 x 126 x 126 cm (49.6" x 49.6" x 49.6") - Weight: 5.7 kg (12.6 lbs.) - The PRS-26 uses the 100-25D Micro-Adjust Clamp - Replaceable jaw covers (part #1960) *NOTE: The maximum weight capacity of the PRS-26 assumes the bike's center of gravity is positioned directly below the clamp.